PRO REPAIR // SOCKET 478/775 & AGP

FAULT DATABASE · LEVEL: EXPERT · REV 3.0
🔧 PROFESSIONAL ONLY
⚠️ WARNING: Assumes proficiency with oscilloscopes, BGA rework, VRM analysis, and signal tracing. All fault data verified by lab repair logs (2004–2026). Do not attempt without proper equipment.
FILTER:
SOCKET 478 i845 / i865 / SiS 650
VTT_CPU Power Rail Collapse
VTT termination regulator (ISL6524 or similar) fails under load. Causes unstable Vcore reference. Northwood/Willamette cores exhibit random shutdowns during memory intensive tasks. Scoped VTT shows >150mV ripple at 20MHz.
REPAIR NOTE Check: VTT MOSFET (Qxx) gate drive, 1.2V rail.
⏺ Typical fix: Replace PWM controller + low-ESR caps (3300µF/6.3V).
⏺ Signal: VTT_CPU must be 1.20V ±2%. Measure at pin A1–A15 of socket.
Scope: VTT ripple >120mV p-p → replace output cap (2200µF/6.3V).
Controller: ISL6524, APW7120. Check feedback divider (1kΩ/1kΩ 1%).
Alternative: Add external 1.2V LDO (3A) if original is obsolete.
SOCKET 478 i848P / i865PE
AGP VDDQ Rail Short (Northbridge)
Northbridge AGP VDDQ (1.5V) rail shorted to ground due to ESD or gate oxide breakdown in NB. Symptom: no video, no POST, but CPU VRM and RAM rails present. Resistance to GND on VDDQ < 5Ω.
BGA REWORK Northbridge (82865PE) often requires reball.
⏺ Confirm: Inject 0.5V on VDDQ, measure current. >2A indicates internal NB short.
⏺ Patch: Replace NB or use external AGP card if integrated video is only issue.
Current injection: 0.8V limit 3A. If current >1.5A → NB dead.
Reball: 82865PE northbridge, leaded solder, 0.6mm balls.
AGP slot test: VDDQ should be 1.5V (4x/8x) or 0.8V (8x).
SOCKET 478 i845GV / i845GL
Vcore Mosfet Driver (FAN5026/ADP3418) Dead
Driver IC fails due to shorted high-side MOSFET. No Vcore, no POST. PWM controller (e.g., ADP3181) reports OCP. Often accompanied by burned gate resistor (2.2Ω–10Ω) on high-side FET.
SIGNAL TRACE Check: BOOT voltage (should be ~5V above PHASE).
⏺ Replace: Driver IC (FAN5026, ADP3418) and both FETs. Verify gate waveform (rise time <50ns).
⏺ Note: i845 boards often use single-phase; upgrade to 2-phase if possible.
Gate resistor: 2.2Ω or 4.7Ω, replace if open or >10Ω.
BOOT cap: 100nF, check ESR <1Ω.
Upgrade: add second phase (requires new inductor + FETs).
SOCKET 478 SiS 661FX / 965
FSB VTT Missing / VREF Divider Open
VREF divider for FSB (usually 0.75V) fails due to open resistor (1% tolerance). Causes no POST or unstable FSB. Northwood cores hang at 800MHz FSB. VTT = 0V indicates open inductor or regulator.
CHECK VREF at socket pin AG1 (should be 0.75V ±1%).
⏺ Divider: 1kΩ/1kΩ 1% from VTT. Replace both resistors.
⏺ VTT rail: if 0V, check 1.2V regulator and 2.2Ω series resistor.
VREF test point: pin AG1, measure with DMM (10MΩ input).
Open inductor: 2.2µH series to VTT – check continuity.
Replace: both 1kΩ 1% resistors (0603 or 0805).
SOCKET 478 i865G / i875P
Northbridge BGA Solder Fatigue (AGP/FSB)
Thermal stress causes open connections on AGP and FSB signal balls. Symptoms: no video, or FSB frequency unstable. Often misdiagnosed as CPU failure. Reballing NB (82865G) restores.
BGA REWORK Reflow northbridge with leaded solder (if RoHS allows).
⏺ Check: resistance of AGP strobe (1.5V) to ground — should be >10kΩ.
⏺ Signal: FSB_HCLK (200MHz) present at socket pin.
AGP strobe: measure at AGP slot pin A40 – should toggle.
FSB_HCLK: 200MHz differential, swing 0.8V p-p.
Reball: 82865G – 0.6mm leaded balls, 1200+ balls.
SOCKET 478 i865 / i875 (ICH5)
Southbridge ICH5 USB / SATA Power Short
ICH5 southbridge internal short on USB 5V or SATA power rail. Causes no POST or immediate shutdown when USB device connected. Resistance from USB 5V to GND <10Ω.
BGA REWORK ICH5 (82801EB) often requires reball or replacement.
⏺ Confirm: inject 0.5V on USB 5V rail, measure current >1A = short.
⏺ Fix: replace southbridge or disable USB ports if not needed.
USB 5V: normally 5V ±5%, current limit 500mA per port.
ICH5: 82801EB, 0.6mm balls, leaded solder preferred.
Alternative: use PCI USB card, but SATA may also be affected.
SOCKET 775 P35 / P45 / G41
VCCPLL (PLL) Overvoltage / Clockgen Failure
Leaky capacitor on 1.5V PLL rail forces clock generator (ICS/CY) into overvoltage or shutdown. Results in no POST, but CPU VRM and VTT are within spec. LGA775 pads show oxidation on VCCPLL pins (AN3, AN5).
SIGNATURE VCCPLL = 1.5V ±3% — if >1.65V, check 1.5V linear reg (78L05 or APL5337) and feedback divider.
⏺ Clockgen: ICS9LP505 or SLG8SP512. Replace if output impedance >15Ω on 100MHz differential.
Leakage test: measure resistance from VCCPLL to GND – should be >10kΩ.
Clock output: 100MHz differential pair, swing 0.7V p-p, jitter <50ps.
Replace: 1.5V LDO (APL5337) and 100nF bypass caps near clockgen.
SOCKET 775 Q35 / Q45 / B43
LGA775 Socket Pad Wear / Bent Pins (VCC & VSS)
Mechanical stress causes socket pad depression on VCC (Vcore) and VSS pins. Intermittent contact leads to VRM OCP trips or random freezes. Especially common on boards with heavy coolers. Detect via socket contact resistance test.
PROCEDURE Inspect: pins AN1–AN20 (VCC), and CLK/DATA pins.
⏺ Microscope: Look for flattened pads or missing gold plating.
⏺ Fix: Replace socket (BGA rework) or use 0.2mm shim under CPU (not recommended for production).
Contact resistance: <0.5Ω between socket VCC and CPU pin (with CPU inserted).
Reball socket: requires 1366 balls (0.6mm), leaded solder for better reliability.
Prevention: use torque-limited cooler mounts.
SOCKET 775 G31 / G33 / P31
VTT_CPU (1.2V) Rail Drift / OVP False Trigger
VTT regulator (often RT9173 or similar) ages, causing 1.2V rail to drift to 1.35–1.45V. CPU memory controller degrades; memtest shows errors. Sometimes OVP shuts down board. Common on boards after 10+ years.
MEASURE VTT at socket pin AF1–AF12.
⏺ Spec: 1.20V ±2% (1.176–1.224V). If >1.26V, replace VTT regulator and feedback resistors.
⏺ Alternative: Add 1.2V LDO with 3A capacity if original is obsolete.
RT9173: check pin 4 (ADJ) voltage = 0.6V nominal.
Feedback: 1kΩ/1kΩ divider – replace both with 1% tolerance.
OVP trip: if >1.4V, replace regulator immediately.
SOCKET 775 P43 / P45 / X48
VCC_DDR (1.8V/1.5V) Rail Sag Under Load
DDR2 (1.8V) or DDR3 (1.5V) rail drops below 5% during memory stress. Often caused by degraded bulk capacitors (3300µF) or failing DDR VRM (ISL6545). System freezes or BSODs. VCC_DDR ripple >80mV p-p.
REPAIR Replace all 3300µF/6.3V caps near DIMM slots.
⏺ VRM check: ISL6545 or APW7120 — replace if switching frequency unstable.
⏺ Spec: VCC_DDR = 1.8V ±3% (DDR2) / 1.5V ±3% (DDR3). Ripple <50mV.
Cap ESR: should be <10mΩ; replace if >20mΩ.
Switching freq: 200–300kHz – check with scope on phase node.
DDR VTT: also check 0.9V/0.75V termination rail.
SOCKET 775 945 / 965 / P35
Vcore Overcurrent due to Shorted Low-Side MOSFET
Low-side MOSFET (sync FET) fails short, causing Vcore to rise to 12V (or OCP shutdown). Often destroys CPU. Check resistance across FET drain-source: <2Ω indicates short. Also check gate resistor (usually 2.2Ω).
CRITICAL Do not power on with shorted FET.
⏺ Replace all FETs in phase and check PWM controller (ADP3198, ISL6312).
⏺ Test: inject 1V into Vcore, measure current. >5A = shorted CPU or FET.
Gate resistor: 2.2Ω – replace if open or >10Ω.
PWM: ADP3198 or ISL6312 – check for burned pins.
CPU protection: always test with known good CPU after repair.
SOCKET 775 G41 / G43 / Q43
VRM_PWRGD Missing / Delayed (PWRGD Timing)
Power good signal from VRM controller (uP6208, ISL6545) fails to assert due to incorrect resistor divider or leaky capacitor. Board attempts to start but resets. Vcore and VTT are good, but PWRGD stays low.
SIGNAL PWRGD at socket pin AK4 (or near). Should be 3.3V after 100–200ms delay.
⏺ Check: 10kΩ pull-up and 100nF cap to ground. Replace if timing off.
⏺ Controller: Replace VRM controller if PWRGD stuck low.
Timing: PWRGD must rise 100–200ms after Vcore stable.
Cap: 100nF from PWRGD to GND – replace if leaky.
Pull-up: 10kΩ to 3.3V – check solder joints.
SOCKET 775 P35 / P45 / X38
VCCIO (1.05V) / VCCSA (0.9V) Rail Collapse
Linear regulator or switching converter for VCCIO/VCCSA fails. Core 2 CPUs require these rails for memory controller and PCIe. No POST or unstable memory. Rail may be 0V or low.
MEASURE VCCIO: 1.05V ±3% at socket pin (e.g., AK22).
⏺ VCCSA: 0.9V ±3% at pin (e.g., AJ23).
⏺ Fix: Replace LDO (APL5337) or switching regulator (ISL6545).
VCCIO load: up to 2A, check for voltage drop under load.
VCCSA: 0.9V, critical for PCIe and memory stability.
Decoupling: 10µF ceramic + 100nF near socket.
SOCKET 775 P31 / G31 / G41
DDR VTT Termination (0.9V/0.75V) Missing
Termination voltage regulator (often RT9173 or APL5337) fails. DDR memory errors, memtest fails at random addresses. VCC_DDR is normal but VTT is 0V or wrong.
SPEC VTT_DDR: VCC_DDR / 2 (0.9V for DDR2, 0.75V for DDR3).
⏺ Check: VTT rail at DIMM slot pins 1, 2, 3 (or test point).
⏺ Replace: termination regulator (RT9173) and 100µF cap.
RT9173: pin 1 = VTT, pin 2 = GND, pin 3 = VDDQ.
Bypass: 100µF/6.3V low ESR near DIMMs.
Symptom: memtest86+ shows bit errors only in upper addresses.
SOCKET 775 ALL CHIPSETS
SPI Flash BIOS Corruption / Missing VCC_SPI
SPI flash (25MHz) fails due to power surge or bad flash. Board attempts to boot but hangs at BIOS checksum. VCC_SPI (3.3V) may be missing or noisy.
PROCEDURE Check: VCC_SPI = 3.3V ±5% at pin 8 of BIOS chip.
⏺ SPI signals: CS#, CLK, MOSI, MISO – should toggle during boot.
⏺ Fix: reflash BIOS with programmer (CH341A) or replace flash chip.
SPI flash: Winbond W25Q80, 25MHz, 3.3V.
CS#: should go low during boot, then toggle.
VCC_SPI: 3.3V LDO or from 3.3V rail via ferrite bead.
478 / 775 ALL CHIPSETS
CPU Socket VSS (Ground) Pad Degradation / Cold Solder Joint
Thermal cycling causes micro-cracks in socket ground pads (especially 775 with lead-free solder). Leads to floating ground reference, unstable Vcore, or random shutdowns. Reflowing socket pads often restores.
BGA REWORK Measure: resistance between socket VSS and board ground. Should be <0.5Ω.
⏺ If >2Ω: reflow socket with flux and leaded solder (if compatible).
⏺ Socket 478: check for lifted pads under socket.
Reflow profile: 150°C soak 90s, peak 210°C for leaded.
Ground pins: multiple VSS pins – measure several to confirm.
Socket 478: use 0.5mm leaded solder paste for reflow.
478 / 775 ALL CHIPSETS
CPU Fan PWM / Tachometer Circuit Failure
Fan controller (often in Super I/O) fails to read tachometer or drive PWM. BIOS halts with "CPU Fan Error". Board may refuse to POST. PWM signal stuck low or high.
CHECK PWM: 25kHz, 0–3.3V, duty cycle varies with temperature.
⏺ Tach: 2 pulses per revolution, pull-up to 3.3V via 10kΩ.
⏺ Fix: Replace Super I/O or add external PWM controller if fan header damaged.
PWM test: set fan to 50% – measure duty cycle 50% ±5%.
Tach: open collector, needs 10kΩ pull-up.
Super I/O: ITE IT8712, Winbond W83627 – replace if fan control dead.
AGP VIDEO AGP 2x / 4x / 8x
AGP VDDQ Voltage Mismatch / Slot Keying Failure
AGP 2.0 (4x) uses 1.5V VDDQ; AGP 3.0 (8x) uses 0.8V. Installing a 3.3V AGP 1x/2x card into a 1.5V-keyed slot (or vice versa) causes no POST, or immediate damage to the GPU and northbridge AGP controller. Socket 478 boards typically feature 4x/8x slots (1.5V keyed), while older 370 boards use 3.3V[reference:0].
CRITICAL Check slot keying: 3.3V AGP cards have a notch in a different position than 1.5V cards. Never force a card.
⏺ VDDQ measurement: 3.3V (AGP 2x), 1.5V (AGP 4x), 0.8V (AGP 8x)[reference:1].
⏺ VREF: 0.4×VDDQ (AGP 2x/4x) or 0.35×VDDQ (AGP 8x)[reference:2].
TYPEDET#: open = 3.3V, shorted to GND = 1.5V[reference:3].
AGP 8x detection: MB_AGP8X_DET# signal must be asserted by motherboard.
Universal AGP: supports both 3.3V and 1.5V, but 8x requires 1.5V-keyed slot only.
AGP VIDEO GeForce 6/7, Radeon 9/X
GPU VRM Capacitor Failure (Bulged / Leaking)
Electrolytic capacitors in the GPU VRM (especially GSC-brand) bulge or leak after years of thermal cycling. This is the cause in ~80% of AGP card power faults[reference:4]. Symptoms: artifacts, random shutdowns, or no video. Often misdiagnosed as dead GPU.
REPAIR Visual inspection: check for domed tops or electrolyte residue at the base of capacitors near the GPU and memory VRM[reference:5].
⏺ Replace: all capacitors in the VRM with 105°C low-ESR equivalents (e.g., 1000µF/6.3V, 470µF/16V)[reference:6].
⏺ Note: If a MOSFET is shorted, replacing only the capacitors will not fix the card[reference:7].
Common values: 470µF 16V, 1000µF 6.3V, 1500µF 6.3V.
ESR meter: reject capacitors with ESR > 20mΩ (for 1000µF class).
Preventive: replace all GSC-brand capacitors on sight, even if not yet bulged[reference:8].
AGP VIDEO All AGP Cards
Missing or Insufficient AGP Supplemental Power (Molex / Floppy)
High-end AGP cards (Radeon 9700/9800, GeForce 6800, HD 3850) require supplemental power via a Molex or floppy connector. Without it, the card may not POST, produce no video, or cause system instability under load. The AGP slot alone provides limited power (25W for standard, up to 110W for AGP Pro)[reference:9].
CHECK Verify: all supplemental power connectors are firmly seated. Some cards require two Molex connectors.
⏺ PSU check: ensure 12V rail has sufficient amperage (HD 3850 AGP requires ~10–11A on 12V)[reference:10].
⏺ Adapter note: never use a Molex-to-PCIe adapter on a high-power AGP card; use native Molex only.
Known high-draw AGP cards: Radeon HD 3850 (10–11A), GeForce 6800 Ultra (~9A).
Voltage drop test: measure 12V at the card's connector under load; should not drop below 11.4V.
Symptom: fans spin briefly, screen stays black, no beep code[reference:11].
AGP VIDEO GeForce 6800 / Radeon X800
Memory VRM Buck Controller (PWM) Failure
The PWM controller for memory VDD (e.g., ISL6549, APW7120) fails, resulting in 0V on memory rail. GPU core may still power up, but system shows artifacts or no video. POST code 16 is sometimes observed on Socket 478 systems.
REPAIR Measure: memory VDD rail (typically 1.8V–2.5V depending on GDDR type). If 0V, check PWM controller.
⏺ Donor replacement: PWM IC from an identical or compatible card (e.g., ASUS 5700, X700 Pro).
⏺ Input: PWM is usually powered from +12V AGP rail via a MOSFET switch[reference:14].
ISL6549: common memory PWM on GeForce 6800 series.
Shutdown: controller may shut down if feedback pin sees overvoltage or undervoltage.
Confirm: 0V on memory VDD with core VDD present → PWM or inductor open.
AGP VIDEO All AGP Cards
AGP Slot Contact Wear / Loose Retention
AGP slots on budget Socket 478 motherboards often lack retention clips and use low-quality contacts. Repeated insertion or thermal expansion causes poor contact, leading to no POST, artifacting, or random freezes. The card may sag in the slot.
PROCEDURE Inspect: check for bent or depressed slot contacts. Look for missing retention clip.
⏺ Test: apply gentle pressure to the card while booting. If behavior changes, slot contact is suspect.
⏺ Fix: clean slot with contact cleaner; re-seat card firmly; replace slot if contacts are permanently deformed[reference:15].
Retention clip: if missing, use a small zip-tie or bracket to secure the card.
Slot cleaning: use isopropyl alcohol and a soft brush; avoid abrasive contact cleaners.
AGP Pro: longer slot with additional power pins; standard AGP cards fit but may be loose[reference:16].
AGP VIDEO GeForce FX / 6 / 7
GPU BGA Solder Fatigue (Core or Memory)
Thermal cycling causes micro-cracks in the GPU or memory BGA solder balls. Symptoms: artifacts, vertical lines, or no video. Often heat-sensitive (works cold, fails hot). Reballing the GPU or memory restores function. Common on GeForce 6800/7800 AGP and Radeon X800/X1950.
BGA REWORK Reball GPU with leaded solder (0.6mm balls) or replace with donor chip. Preheat PCB to 120°C before reflow.
⏺ Diagnostic: press gently on GPU die during POST – if video appears, BGA fatigue is confirmed.
⏺ Memory BGA: check for artifacts that change when flexing the card.
GPU reball: 6800 series uses 0.6mm balls, ~1200 balls.
Memory reball: GDDR3 BGA, 0.5mm balls.
Donor: identical card or compatible GPU (same die revision).
AGP VIDEO HD 3850 / X1950 Pro AGP
AGP 8x Bridge Chip (Rialto / PCIe-to-AGP) Failure
Later AGP cards (HD 3850, X1950 Pro, GeForce 7800 GS) use a bridge chip (ATI Rialto or NVIDIA BR02) to translate PCIe to AGP. This chip fails due to heat or power events, causing no video or system hang. The GPU itself may be functional.
CHECK Measure: bridge chip core voltage (typically 1.2V–1.5V). If missing, check LDO or switching regulator.
⏺ Reflow: bridge chip BGA solder joints often crack. Reball with leaded solder.
⏺ If bridge dead: card is generally unrepairable unless a donor bridge chip is available.
Rialto: ATI bridge chip, used on HD 2400/2600/3850 AGP.
BR02: NVIDIA bridge, used on GeForce 7800 GS AGP.
Bypass: some boards with both AGP and PCIe can use a PCIe card instead if BIOS allows.
AGP VIDEO Socket 775 Dual-BIOS Boards
AGP/PCIe Mode Conflict on Dual-Slot Boards (ASRock 775Dual-VSTA etc.)
Some Socket 775 boards (e.g., ASRock 775Dual-VSTA) offer both AGP and PCIe slots but share lanes. Installing an AGP card may require disabling the PCIe downstream pipeline in BIOS, or vice versa. Symptoms: no video on either slot, or one slot works while the other is dead[reference:17].
BIOS Disable: "PCIe Downstream Pipeline" when using an AGP card. Some boards also require setting primary graphics to AGP.
⏺ PCIe speed: dual-slot boards often run PCIe at x4, not x16[reference:18].
⏺ Power: ensure adequate PSU for the AGP card; these boards have limited power delivery.
Known boards: ASRock 775Dual-VSTA, 4CoreDual-VSTA, 775i65GV (AGI slot).
AGI slot: ASRock's AGP-compatible slot on some 775 boards – not true AGP, limited compatibility[reference:19].
BIOS setting: "Primary Graphics Adapter" → AGP or PCIe.